Mostra i principali dati dell'item
dc.contributor.author | Ощепков, Б. В. | |
dc.contributor.author | Ощепков, Г. Ф. | |
dc.contributor.author | Жильцова, Т. А. | |
dc.contributor.author | Oshchepkov, B. V. | |
dc.contributor.author | Oshchepkov, G. F. | |
dc.contributor.author | Zhil'tsova, T. A. | |
dc.date.accessioned | 2015-08-03T09:01:14Z | |
dc.date.available | 2015-08-03T09:01:14Z | |
dc.date.issued | 2014 | |
dc.identifier.citation | Ощепков, Б. В. Некоторые особенности производства сплава ХН70Ю / Б. В. Ощепков, Г. Ф. Ощепков, Т. А. Жильцова // Вестник ЮУрГУ. Серия Металлургия.- 2014.- Т. 14. № 3.- С. 71-74.- Библиогр.: с. 73 (6 назв.) | ru_RU |
dc.identifier.issn | 1990-8482 | |
dc.identifier.uri | http://dspace.susu.ac.ru/xmlui/handle/0001.74/5032 | |
dc.description | Ощепков Борис Владимирович, канд. техн. наук, доцент кафедры общей металлургии, Южно-Уральский государственный университет, филиал в г. Златоусте (г. Златоуст); splav.zlat@mail.ru. Ощепков Георгий Фёдорович, студент, Южно-Уральский государственный университет, филиал в г. Златоусте (г. Златоуст); gosha1991.03@mail.ru. Жильцова Татьяна Анатольевна, старший преподаватель кафедры общей металлургии, Южно-Уральский государственный университет, филиал в г. Златоусте (г. Златоуст); zilcova79.ru@mail.ru. B.V. Oshchepkov, South Ural State University, Zlatoust Branch, Zlatoust, Russian Federation, splav.zlat@mail.ru, G.F. Oshchepkov, South Ural State University, Zlatoust Branch, Zlatoust, Russian Federation, gosha1991.03@mail.ru, T.A. Zhil'tsova, South Ural State University, Zlatoust Branch, Zlatoust, Russian Federation, zilcova79.ru@mail.ru | ru_RU |
dc.description.abstract | Качество полученного сплава в значительной степени определяется технологической пластичностью металла. Настоящая работа направлена на изучение причин пониженной технологической пластичности сплава ХН70Ю и разработку мероприятий, направленных на её повышение. Известно, что высокотемпературная хрупкость сплава ХН70Ю связана с влиянием интерметаллидов и карбонитридов на границы зёрен металла. Нами предложено давать хром уже в жидкую ванну, что существенно сокращает время его плавления и, следовательно, уменьшает время насыщения металла азотом. Известно, что позитивное влияние на длительную прочность сплава могут оказать небольшие добавки циркония. Показано, что максимальная длительная прочность достигается при содержании циркония порядка 0,1 мас. %. Цирконий связывает азот, однако для более полного удаления азота из метал- ла предложено изменить порядок ввода циркония в сплав, разделив его присадку на два этапа. Одна часть циркония (0,05 мас. %) дается в сплав в конце плавления, а вторая (0,05 мас. %) в ходе рафинирования, совместно с алюмо-бариевой лигатурой и церием, ближе к выпуску металла из электропечи. Как показала практика, внедрение совокупности предложенных мер при производстве сплава ХН70Ю позволило снизить содержание азота в кованых заготовках в среднем с 0,025 до 0,018 мас. %. Относительное удлинение в листе повысилось с 59 до 65 %, и в результате количество листов первого сорта увеличилось с 40 до 70 % от общего количества. The quality of the alloy produced depends greatly on the technological metal plasticity. The present research aims at studying the low technological plasticity reasons of the CrNi70Al alloy and developming measures focused on its improvement. It is known that high-temperature brittleness of the CrNi70Al alloy is related to the influence of intermetallides and carbonitrides on metal grain boundaries. We proposed to put chrome in a liquid metal bath which significantly reduces melting time and therefore reduces the time of metal saturation by nitrogen. It is known that positive impact on long-term strength of the alloy can be obtained with small additions of zirconium. It is shown that the maximum long-term durability is achieved when the zirconium content is about 0.1 wt. %. Zirconium binds nitrogen, however, it was proposed for more complete removal of nitrogen in the metal to change the order of zirconium input in the alloy dividing its feeding into two stages. One part of zirconium (0.05 wt. %) is put in the alloy at the end of melting, and the second (0.05 wt. %) is put during refining together with alumobarium ligature and cerium close to the metal tapping from the furnace. It was shown that the introduction of measures proposed during the production of the CrNi70Al alloy allowed to reduce the nitrogen content in forgings on average from 0.025 to 0.018 wt. %. Tensile sheet strain increased from 59 to 65 %, and as a result the number of the first class sheets increased from 40 to 70 % of the total number. | ru_RU |
dc.language.iso | other | ru_RU |
dc.publisher | Издательский центр ЮУрГУ | ru_RU |
dc.relation.ispartof | Вестник ЮУрГУ. Серия Металлургия | |
dc.relation.ispartof | Vestnik Ûžno-Ural’skogo gosudarstvennogo universiteta. Seriâ, Metallurgiâ | |
dc.relation.ispartof | Bulletin of SUSU | |
dc.relation.ispartofseries | Металлургия;Том 14 | |
dc.subject | УДК 669.24 | ru_RU |
dc.subject | никелевые сплавы | ru_RU |
dc.subject | выплавка | ru_RU |
dc.subject | технологическая пластичность | ru_RU |
dc.subject | nickel-based alloys | ru_RU |
dc.subject | smelting | ru_RU |
dc.subject | technological plasticity | ru_RU |
dc.subject | ГРНТИ 53.37 | ru_RU |
dc.title | Некоторые особенности производства сплава ХН70Ю | ru_RU |
dc.title.alternative | Some features of CrNi70Al alloy production | ru_RU |
dc.type | Article | ru_RU |